Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32

Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32

Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32
Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32 Digital display Rapid Warming TSTips InterfaceDC5525. Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32 Digital display Rapid Warming TS Tips Interface DC5525. This soldering station has no Power supply! NOTE:Iron tip do not work continuously high temperature, high temperature work is easy to damage the tip! Ordinary solder melting point is 183°C, lead-free solder melting point is 227°C, usually the welding temperature is 300-380°C, 380°C is the temperature of the dividing line, higher than 380°C, iron head oxidation and loss is extremely fast, seriously affect the heating core life The Higher than 380°C temperature display will be beating, the higher the temperature, the greater the beating! Recommended in the 300-380°C for welding work, most of the work can be carried out, the temperature beating is normal, does not affect the use! Temperature Stability: 2 degrees Celsius. Output Temperature: 100-400 degrees Celsius. 1 x Soldering iron control terminal (this is original). 1 x Hexagon device. SET1:TS-I TS-BC2 TS-K (just one TS iron tip is original). SET2:TS-I TS-BC2 TS-K TS-D24 TS-KU. Just one TS iron tip is original. SET3:TS-I TS-BC2 TS-K TS-D24 TS-KU TS-B2 TS-C4. Why the temperature of the new T12 solder tip is jump? Because the inside heating core of the new T12 solder tip did not go through the high temperature, so the first time to use will be a bit of temperature, generally without special treatment, the normal use of 1-2 days after the basic will not bounce. Such as the need to immediately effective, the general proposal to adjust the temperature to 380 degree -400 degree, side of the solder tip to the tip of tin, burning 5-10 minutes after the shutdown, until the solder tip of the cooling and then re-boot! (if 1 times no effect, then can be repeated 2-3 times). T12 is pulsating temperature warming, even if the display temperature is flashing, the tip of the real temperature is completely stable. T12 jump temperature also are connected with the temperature control board of procedures, power of electrostatic and if it connect the ground. What the problem of attention when we use the T12 first time? T12 tip heating speed is very fast, when the new solder tip connect the electricity, it must be tinput immediately to the solder tip, for protection, due to heating up fast, just need 6-10 seconds, no have more time to you for preparetion. What are the precautions for using the T12 tip? If can use low temperature, then do not high temperature: T12 is constant temperature control, the general recommended working temperature control between 300 degree- 380 degree, higher than 380 degree damage the coating of solder tip and cut down the PTC life! Do not dry: the first time to use solder tip, should be wrapped while heating a layer of tin. If it’s without work, at once shutdown! Diligent to clean: before shutting down, use a wet sponge or detin the ball to remove the tip of the oxidation of debris, on the tin after the shutdown power off! Standard operation: Do not violent collision the solder tip, do not stamp the top of the hard objects, but can not be used to hot plastic and other materials, specifically reminded that friends like tin should avoid the iron and other hard metal knock tin, the heating core of T12 is in the head of the solder tip, often percussion is a fatal damage to T12! Less use of scaling powder: scaling powder can not be used, can be used as less as possible! When scaling powder help make beautiful and reliable welding at the same time, but also greatly speed up the consumption the coating of the solder tip, T12 heating core high temperature position is very near of the Nozzle tip of the solder tip, Scaling powder in the fear of threat to T12 head pressing parts. The item “Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32″ is in sale since Wednesday, February 24, 2021. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Soldering/Desoldering Equipment & Accessories\Soldering Guns & Irons”. The seller is “il_av22″ and is located in Shanghai. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Australia.
  • Item Type: Programmable Soldering Iron
  • Temperature Stability: +-3C
  • Input Voltagle: 12-24V
  • Output Power: 65W
  • Output Temperature: 100-400C
  • Origin: CN(Origin)
  • Certification: NONE
  • Dimensions: 168mm
  • MPN: Does not apply
  • Brand: LAECHO

Mini Portable TS100 OLED Programmable Electric Soldering Iron station STM32

Comments are closed.